umtec Halle GmbH
About us
As an owner-managed family business, we have been successfully
successfully on the market for three decades now and have continuously
product portfolio since 1990. In doing so, we have always
personalised and individual advice for our customers has always been particularly important to us. Thanks to the extensive expertise of our employees and our large network of partner companies, we are able to offer optimally customised solutions
Products
Stand frames silo
If you want to protect sensitive technology from wind and weather, a stand-alone silo is just the ticket. By extending the sheet steel cylinder to the floor, plant components can not only be protected from premature wear. Heating and insulation of the space under the cone is also possible in this way. The compact arrangement of dosing and discharge technology means that even complete plants can be accommodated within stand-alone silos. Lime milk plants are an example of this. These can be completely assembled and wired in the factory and are ready for use on site after a short time. Go ahead and ask us about them! We would be happy to hold talks with you about what appearance a sensible solution might take
umtec cartridge filters
By contrast with the filter elements in the BFE filter, the cartridge filters are almost always flowed against from below. The regeneration of the elements also takes place using compressed air. The main advantages of the cartridge filters are the overall more compact design of the filter and the high operating temperature of max. 260°C. These are normally raw gas flows from thermal processes. You would like to know more about the umtec cartridge filters? Go ahead and ask us about them!
Tubular screw conveyor
In order to overcome short to medium distances, which can have a gradient of up to 45°, a tubular screw conveyor is the best choice. In this way, dry bulk materials can be transported particularly efficiently and - due to the enclosed transportation - dust-free. Tubular screw conveyors are suitable for powdery to fine-grained bulk materials. We will be happy to inform you about the options available in meeting your individual requirements!
Planning & design
Good planning is an important prerequisite for a successful project. We develop customer-oriented solutions in the field of bulk materials handling and can incorporate new innovations in the process. After an analysis of the situation at the customer's site, everything is adapted to the conditions on site during the planning phase. The construction work is performed in-house here. This offers two decisive advantages. On the one hand, information loss is avoided, and on the other, CAD modelling using Solid Works enables rapid visualisation and detailed presentation. The direct dovetailing with our own manufacturing ensures short distances - so corrections can also be made during the production phase without any further ado
In-house manufacturing
We produce all our silos and plants in our own factory in Halle (Saale). By bundling the design with the production at one location, it is possible for us to respond quickly to any changes that may occur or to identify problems at an early stage. We can respond flexibly to your wishes with our state-of-the-art production facilities. For instance, the plasma cutting machine, tube cutting machine and CNC bending machine receive data records directly from the technical office. In this way, solutions from the 3D programme are transferred directly to the production technology and implemented in the shortest possible time. You want to know more about our manufacturing options? Go ahead and ask us about them!
Mobile water treatment plant
Contaminated deep water or surface water is also recycled in mobile water treatment plants. The special feature here: the mobile facilities can be completely dismantled and the site can thus be renaturalised. The process steps of aeration, flocculation and sedimentation are carried out as individual modules in differently equipped roll-off containers. This modular system offers maximum levels of flexibility and can be optimally adapted depending on the location. We would be happy to clarify with you what appearance a customised solution might take!
Statics
Silos fall under the legislation for structures - i.e. a static calculation according to a European-wide standard (EN 1090) is mandatory. In order to be able to guarantee a smooth process from the planning to the installation of the silo, we also consistently implement this service "in-house". This enables direct coordination between the structural design and the static requirements without detours - by way of a customer-oriented solution finding process. We use the finite element method to calculate forces in and on the silo. This enables us to perform even very complex designs and simulations. (Software: RFEM). Any questions? We will be happy to advise you!
Standard silos
Standard silos are used for the space-saving storage of loose, dry bulk materials. The designs differ according to the material to be stored and the subsequent installation site, among other things. There are the following options: Various cone inclinations Flat bottoms Insulation and heating Double chamber and multi-chamber silos Integration of the most diverse components (e.g. filter or bucket elevator, load cells) Factory-welded standard silos from umtec can be manufactured with a diameter of 2,400 - 4,200mm and a capacity of 15 - 300m³. The silos can be filled or emptied either mechanically or pneumatically. We will be happy to inform you about the options available in meeting your individual requirements!
Multi-chamber silos
Multi-chamber silos are the optimal way to store several bulk materials in a small space - space-saving, cost-saving and with short discharge distances. Possible designs are two-, three- or even four-chamber silos, each with a single or double partition wall. Either outlet plates or trouser outlets are available as outlets. Would you like to know more? Contact our competent staff – We will be happy to advise you!
Bolted silos
Bolted silos are the best solution when a particularly large usable volume is required. Silos with a capacity of 150 - 1,000m³ and a diameter of 4,500 - 7,000mm can be realised. They are often used to store loose bulk materials such as gravel, crushed stone or grit. Umtec plans and designs individual silos or entire plants for you in 3D, which are then manufactured in our own factory in Germany and assembled on site. Bolted silos are available in various designs: Double and multi-chamber silos Partition wall silos (single or double shell) Various cone inclinations, flat bottom with substructure extension and intermediate platform as loading silos We would be happy to hold talks with you, about what appearance your solution might take!
Pressure shock resistant silos
If explosive bulk materials such as coal, flour or sewage sludge granulate have to be stored, then pressure-shock-resistant silos are the solution. An individual P&I diagram with complete safety equipment is created for each user case - for the safe operation and filling of the silos in accordance with ATEX standards. We offer pressure-shock-resistant silos preferably in diameters of 3,200 - 4,200mm and with a volume of 70 - 300m³. Depending on the product and silo size, the following equipment is realised: Temperature monitoring Explosion protection flaps Rupture discs Inertisation (incl. clean gas or raw gas analysis). We also offer our own service for the maintenance of pressure-shock-resistant silos: Electrical function test - preliminary acceptance at the factory Engineering commissioning with personnel briefing Professional inspection, including acceptance of the explosion damper (regularly at 12-month intervals) Would you like to know more? Get in touch with our competent staff! We will be happy to advise you!
Job ads
Metal worker / fitter
We are looking for metalworkers in the production area to take over the assembly and locksmith work, taking occupational safety into account. areas of responsibility Independent execution of assigned tasks according to work instructions, including: Operation of machinery (edging, saw, shears, roller, press, welding machine) Working from drawings Manufacture of add-on parts Manufacture and welding of individual components Silo completion with add-on parts Checking of your own work after completion with countersignature on the production run card Independent implementation of correction work after consultation with the workshop manager Creation of partial purchases cooperation The job holder works closely with workshop management and TB to complete the tasks that arise as best as possible and together. Consultation with the project manager is also recommended, as he has the closest customer contact.
Industrial electrician/mechatronics technician
For the new start of our electrical department we are looking for an industrial electrician/mechatronics technician (m/f/d). Responsibilities: Independent execution of assigned tasks, including: Supervision of the entire electrical department Support and independent realisation of projects Coordination and control of orders New installation of electrical systems Repair of electrical systems Commissioning, maintenance and troubleshooting of industrial systems Qualifications: Completed vocational training as an electrician or comparable training Several years of professional experience MS Office knowledge Experience in commissioning, maintenance and troubleshooting of industrial plants Class B driving licence We offer above-average remuneration 30 days holiday Short decision-making processes due to flat hierarchies Provision of a company car