KREISEL two-way distributors are used to direct the flow of bulk material optimally.

The Claudius Peters Two-Way Gate is installed in aeroslide systems to guide and control the mass flow. The Two-Way Gate consists of a cylindrical housing. Sealing of one outlet each is carried out by an adjustable gate. By turning the drive shaft, the gate shifts from one material outlet to the other. A flexible sealing ensures that the outlet is sealed dust-tight. The drives can be pneumatic, motoric or manual and are designed with sufficient reserves so that even under aggravated conditions a safe operation is ensured. For cleaning of the Two-Way Gate and for inspection of the gate sealing, the housing is equipped with a large inspection cover. Replacement of the wear parts (aeration fabric and gate sealing) can take place while the Two-Way Gate remains installed by disassembling the top cover or the bottom. Lubrication of the bearings or the drive is not necessary. The end positions can be precisely adjusted and can be indicated by limit switches integrated in the drive.

Application area: The tube switch is mainly used in delivery lines of high pressure systems; however it can also be used in the low pressure range at any time. It is suitable for the transport of dry, non-adhesive or tending to cake dusts and is used for changing the direction of the delivery flow. Material: Case: grey cast iron or cast stainless steel Shut-off cone: grey cast iron or cast stainless steel Seal: rubber, silicone, Viton Design: The tube switch consists of the tube switch case, the swivel arm with the shut-off cone and the pneumatic swivel drive. The closed outlet is sealed with a sealing ring which is pressed against a hardened ring. Electrical equipment: The tube switch has a limit switch (normally closed contact and normally open contact) in each end position at free choice for standard signalling. A Herion 5/2 way solenoid valve is usually used as control valve (other makes of control valve on request). The electrical equipment is supplied in any protection type and any common voltage according to requirement. Operating data: control pressure: approx. 5 bar operating pressure: max. 10 bar Special features: The tube switch guarantees faultless sealing of the stopped delivery stream so that material mixtures in the case of conveying different materials via one system are ruled out. The advantage of this design is that the sealing rings can be replaced without dismantling and shortest standstill times. A different switch design must be selected for the conveyance of adhesive and caking materials. The tube switch can of course also be supplied with electric motor drive and with manual actuation.

Application: silos, hoppers, pipes Powder: fine and dust [cement and lime] Problem solving: bridge and rat-holing FEATURES duty cycle: continuous working pressure: from 0.2 bar to 1 bar pneumatic circuit: filter + flow control valve air supply quality: class 5.4.1. working temperature: from -20°C to 80°C max. noise level: < 100 dB(a) technology: fluidification material: U060 - ring carbon steel, sintered PE filter, PS body / U025 - ring carbon steel, sintered brass filter, PE body

Super fine grinding plants, grinding and drying plants and simultaneous grinding and drying plants, type ULTRA-ROTOR, especially for: food, minerals (drying free of agglomerates), vegetables and animal proteins, special chemicals and everything which is difficult to be treated on conventional plants. ULTRA-ROTOR plants treat sticky materials, explosive materials and corrosive materials. They are used as grinders, dryers, mixers, as well as for surface coating (coating of minerals with stearic acid). From individual machines to complete plants and subsystems is our scope of delivery. Minimal wear and tear costs due to particle to particle interaction. Heavy robust construction, extremely long and trouble free operation. We customize each application to the individual customer's requirements. Cryogenic grinding, grinding under inert atmosphere, grinding and drying under steam atmosphere are available.

This system prevents sticking and adhering of dry bulk materials to the inner metal surfaces and ensures a continuous product discharge

Umlenkrolle für Reißleine

By contrast with the filter elements in the BFE filter, the cartridge filters are almost always flowed against from below. The regeneration of the elements also takes place using compressed air. The main advantages of the cartridge filters are the overall more compact design of the filter and the high operating temperature of max. 260°C. These are normally raw gas flows from thermal processes. You would like to know more about the umtec cartridge filters? Go ahead and ask us about them!

KAESER’s FBS and GBS rotary screw blowers set the new standard in efficiency and space-saving design. The SFC version is equipped with an integrated frequency converter and a synchronous reluctance motor. The STC version for fixed-speed operation is now also more efficient than ever before. These innovative rotary screw blowers not only impress with their energy-saving drive concept, but also with their well thought-out and compact design, which allows all maintenance work to be performed from the front of the unit. Side-by-side installation is possible even with all electrical equipment.

UNIGLASS is a conveyor belt with a special cover, resistant not only to the abrasion, (~45 mm3) but also to rips and cuts. This cover has been specially designed to extend your conveyor belt life carrying the most abrasive and aggressive materials.

Wherever it is necessary, for reasons of height or space, the chevron conveyor belt UNILIST will help you conveying your material over angles of 22°. The wide range of cleats of 15 mm, 17 mm, 25 mm, 30 mm and 32mm heights and the variety of their widths will solve your problems.

UniSort BlackEye - Bulk goods sorting Reliable sorting of dark objects by type of plastic using HSI UniSort BlackEye is the logical further development of our HSI technology. The camera-based STEINERT technology is also used here. The difference to the standard HSI camera lies primarily in the frequency range analysed. Our UniSort BlackEye, for example, is able to separate light-coloured and black polymers from each other. As with the UniSort Finealyse, mixtures of materials of the same size (50 / 50 fractions) can also be separated in one sorting stage. Because the UniSort BlackEye has the same design as the UniSort Finealyse, it is also characterised by low oversorting. The highly effective STEINERT UniSort BlackEye sorting device separates bulk materials for you in the fraction range of 10-40 mm. It consists of a feeding and dosing unit with a material hopper, an acceleration conveyor belt, a collecting bonnet and a compressed air nozzle bar. Your benefits at a glance: - UniSort BlackEye brings system into the dark: sorts black plastics by type Low oversorting - Conveyor belt system (no chute) - Fraction size: 10-40 mm - Adaptive for different sorting criteria - Precise detection and discharge

NIR sorting unit with Hyper Spectral Imaging camera technology for optimised sorting of 2D materials Up to 50% more throughput than standard systems Lightweight 2D fractions such as plastic film and bags, as well as paper and fibres, tend to float at high belt speeds due to their low weight per unit area and can only be sorted at low throughput rates with conventional systems. For good performance, all objects should also be separated on the belt and overlapping objects should be avoided. This is less of a problem for applications with 3D material, as the transfer of the objects to the acceleration belt usually ensures sufficient separation. This separation is much more challenging for lightweight 2D components. This is because these flat objects tend to fly and cannot be accelerated to the usual high belt speed of 3 metres per second. As a consequence, the speed of the acceleration belt is usually significantly reduced, which minimises the tendency to lift off (fly) on the belt. However, reducing the belt speed is counterproductive - especially in the area of lightweight 2D objects: Low basis weight combined with reduced belt speed further shrinks the possible throughput per metre of working width of the separator. This makes sorting uneconomical overall due to the large working widths required. The five most important innovations of the UniSort Film EVO 5.0 at a glance: - Innovative belt cover - Optimised ventilation plates - New maintenance flaps - Dynamic calibration - Automatic white balance

NIR sorting unit with Hyper Spectral Imaging camera technology State of the art - camera-based NIR technology for even better sorting results It has been more than 20 years since the first near-infrared (NIR) detection systems, originally developed for the food industry, found their way into recycling. A lot has happened since then, both in terms of the sensors available and the analysis algorithms used: Mobile phones recognise their rightful user with the built-in camera and cars drive themselves along the motorway. These are just two examples of the rapid development of sensor-based applications. With so many developers working on these topics worldwide, it was only a matter of time before camera-based systems also became standard in NIR sorting units. The fifth evolutionary stage of the proven UniSort PR builds on this foundation, refines it and paves the way for the next era of waste sorting technology. With the UniSort PR EVO 5.0, STEINERT is building on years of experience from the use of several UniSort generations and mass data processing. This forms the basis for further advances in sorting performance, but also for the optimisation of processes in the value chain. This enables its users to adapt flexibly to changing material flows and to recognise new potential, but above all to make use of it. The five most important new features of the UniSort PR EVO 5.0 at a glance: - Revised lamp boxes - Improved valve bar - Dynamic calibration - Automatic white balance - Object recognition

The multi-functional Universal Mill offers flexibility in particle size distribution and capacity for the grinding of soft to medium hard products with a Mohs hardness of up to 4-5. • shock pressure resistant up 10 bar(g) • certified according ATEX - 2014/34/EU • available in carbon or stainless steel materials MAIN APPLICATIONS • sugar • gypsum • spices & herbs • instant coffee • legumes • presscakes • grains & seeds • dairy • hydrocolloids (starch, celllulose, etc.)