Physical processing - Processing and sorting methods for materials and waste streams with complex structures and compositions - Electrohydraulic fragmentation - Impact crusher - Modular sorting plant - Laboratory equipment Chemical processing - Development of chemical separation technologies - Recovery of valuable materials by gas phase reactions - Leaching and extraction processes Biological processing - Development of bioleaching processes for the recovery of metals from magnetic materials, slags, ashes or electronic waste

Flat construction - gently conveying Application: For energy-saving conveying of piece goods and bulk materials over long distances up to 25,000 mm Conveyed material: Wooden materials, foodstuffs, chemicals or the environmental sector Benefits: · Adjustable conveyor output · Low-maintenance continuous operation, low operating costs · Gently conveying of the product · Compact flat construction for conveyance over long distances · Energy-efficient system · Vibration-isolated dual-mass systems with very low adjusting forces. · Quiet operation

The feeder system of the series FlexiLink consists of a pneumatic linear vibrator from our series NTK, blade springs and the FlexiLink connector element. This system uses the natural resonance of the springs to move bulk materials along the conveyor. Once the trough starts to vibrate at the resonance frequency, maintaining the vibration requires very little additional energy. Even with varying loads, the trough continues to vibrate with the correct resonance. The amplitude can be adjusted by means of an optional exhaust throttle. In addition to driving classic feeder troughs, the FlexiLink system can be used to drive bowl feeders, by arranging the blade springs in a circle to accommodate the spiral feeder. Customised versions of the FlexiLink series are available and all components can be purchased separately.

Are you faced with the decision of whether to modernize your automated production system or buy a new one? Especially with older machines with good mechanics, modernization and replacing the automation is often the more economically sensible option.

Gradually modernize controls and processes. SCADA systems PLC systems HMI systems control cabinets cabling sensors and actuators All from a single source! From engineering to assembly and commissioning!

Regular rollers reliably prevent conveyor belt misalignment and simultaneously protect the sensitive belt edges. To ensure flawless operation even under real-world conditions, the rollers are equipped with a dirt-repellent special rubber (60° Shore). This ensures stable function even if the drum shell is not completely clean. Our regular rollers are suitable for both standard and reversible conveyor belts and offer a robust, low-maintenance solution for daily use. How it works: When the belt is running straight, the longitudinal axis of the roller shell is at a 90-degree angle to the direction of travel of the conveyor belt. If the belt misaligns, the roller shell tilts slightly forward due to the belt's own weight, creating a pre-run. This pre-run counteracts the misalignment and automatically returns the belt to the correct position. As soon as the belt is running smoothly again, the roller shell returns to its starting position. This self-regulating movement is made possible by a central ball joint and the defined axis position.

Reversing scraper The FTK standard reversing scraper is for use on light to heavy conveyor belt systems. This scraper was specially developed for reverse operation. By means of a technology adjusted to its optimum for this process, the scraper aligns itself to the belt cover during its work process at an angle of 90 degrees. In reverse operation, the scraper automatically adopts a slightly dragging position and thus prevents vibrations and excessive wear of the belt cover. Belt speeds of up to 2 m/s with the mini-model. Belt speeds from 2 m/s with the reinforced model. specially for use with extremely adhering and abrasive materials and damaged belts and having only a minimal installation height. Areas of use: various plants, e.g. for sand, gravel, recycling, compost, clay, brick, asphalt-mixing plants and in the gypsum, cement and glass industries etc. Any products adhering to the belt reduce the life expectancy of the conveyor due to the heavy soiling. The consequences are usually expensive maintenance measures and production down times. The FTK Förderband Technik Kilian belt conveyor scrapers represent a cost-effective development in the field of belt cleaning. Due to the flexible mounting arrangements and the non-belt-damaging but thorough cleaning, the FTK Förderband Technik Kilian belt conveyor scrapers lead to higher productivity combined with only minimal purchase price and running costs.

GeDe Kugellager-Vertriebs-GmbH offers split cylindrical roller bearing housing units that are the perfect solution for applications requiring high loads and easy handling. The split housing design allows for quick and easy installation, especially in confined spaces or existing systems. These units offer high load capacity and long service life, while the robust housing reliably protects the bearings from external influences. With wide availability and flexible solutions for various industries, including conveyor technology, mechanical engineering, and heavy-duty applications, split cylindrical roller bearing housing units offer a cost-effective and time-saving solution. Translated with DeepL.com (free version)

The RFnivo® level limit switch is universally applicable in solids and liquids as a full, demand or empty detector in silos and containers. The different device versions withstand extreme process conditions and due to their stainless steel components, are very robust. The RFnivo® measures the capacitance between the probe and container wall. If the probe is covered by the product, the measured capacitance changes and a switching signal is activated. Since each container is different in geometry, the RFnivo® must be calibrated after installation. This is done automatically once the supply voltage has been connected or by pressing the calibration button on the unit. All versions of this device are complete with "Active Shield Technology" which ensures the probe is insensitive to any material build up or caking. This ensures complete reliability of the probe. International certifications for Hazardous Locations (gas and Dust Ex) ensure the device is suitable for a wide range of applications in all industries.

RFnivo® 8100 - Standard Version • Full, Demand, Empty Detector • Shaft is selectable as - Rod version (vertically, horizontally and oblique installation) - Rope version (vertical installation) • Wide range of applications in liquids and solids. • Suitable for use in applications with high pressure - up to 35bar and process temperatures up to 200°C. • Measurement of low DK values (from 1.5). • Active Shield Technology against material build-up. • Electronics housing made of die-cast aluminum, protection class IP 68/NEMA 4. • Approvals for hazardous locations (gas and dust-Ex). • High chemical resistance on probes. • No maintenance RFnivo®8200 - High Temperature Version • Full, Demand, Empty Detector • Suitable for process temperatures of up to 400°C • Rod version (vertical, horizontal, oblique installation) • Wide range of applications in liquids and solids. • Suitable for use in applications with high pressure - up to 35bar and process temperatures up to 400°C. • Measurement of low DK values (from 1.5). • Active Shield Technology against material build-up. • Electronics housing made of die-cast aluminum, protection class IP 68/NEMA 4. • Approvals for hazardous locations (gas and dust-Ex). • High chemical resistance on probes. • No maintenance

Rhino Hyde® – the heavy duty material that protects against abrasion. With a resistance to wear up to 20 times higher than steel, our product can be used wherever abrasive, aggressive bulk goods, such a grain, glass concrete or scrap metal, are transported. Rhino Hyde® is associated with good formability and a wide range of processing options for your individual application. Choose economic efficiency and use Rhino Hyde® to increase the service life of your machines and systems. PROPERTIES: • Sound absorbent • Shock absorbent • Protects products • Suitable for use with food • Low adhesion • Antistatic • Largely resistant to acids and alkalis • Cut resistant • Suitable for cold forming • FDA approved SECTORS: • Silo and storage businesses • Sand, gravel, calcium, and ore extraction • Concrete production • Recycling industry • Shot-blasting businesses • Press operators, etc. EXAMPLE OF APPLICATION: • Vibrating troughs • Mixers • Elbow pipes • Chain and screw conveyors • Elevators • Chutes • Pipelines • Collapsible crates • Segments

Due to its high abrasion resistance Rhino Hyde® can also be used as scraper for chain conveyers. Advantages like reduction of noise and increase of flowability without any caking will make the work flow easier than ever. It is easy to install - after cutting to required length, the scraper will be pushed over the steel core. PROPERTIES: • High abrasion and impact restistance • Increases noise • Easy to customize • Temparture operation range up to 80°C • Corrosion resistance • No caking • Installation without disassambly • Hardness (Shore A) 80

With Rhinox we complete our range of materials for corrosion protection in bulk material industry applications. Rhinox is a two-component moulded material made from highly abrasion-resistant grained ceramic and epoxy resin. It is used in all areas where Rhino Hyde is too stiff or where media are conveyed at high speed. In addition, Rhinox is successfully used in applications where highly corrosive and sharp-edged materials (such as in recycling) are conveyed under dry or wet conditions. Rhinox is also a proven material for repairing slides, grooves, tubes, curved elements, pipe or tube magnets, pumps, ventilators, separators and curves in suction plants and features these outstanding product characteristics: • it absorbs impacts • it is chemical resistant • temperature operation range –30° to +120°C Available packages: 2 cans consisting of 2.25 kg (1x 1.5 kg of resin and 1x 0.75 kg of hardener). This quantity is sufficient for an area of approx. 100 x 15 cm with a coating thickness of approx. 8 cm.

The welded or looped RIMA® and CORIMA wedge wire screens from HEIN, LEHMANN can be individually adapted to any application and therefore used universally. They are unbreakable, they only know about constipation problems by hearsay, and that's not the only reason why they improve screening efficiency in almost all branches of industry.