Accessories for pinch valves: KVT pinch valves are generally operated with oil- and water-free compressed air. As a rule of thumb, the closing pressure should be approximately 2 bar higher than the medium pressure in the pipeline. Therefore, please install a maintenance unit with oil removal, a strainer, and drainage, as well as a pressure reducer, upstream of the electromagnetically or manually operated valves that control the pinch valve. Position indicators: Position indicators (electrical/optical) can be used to check and provide feedback on the closed position. Do you need help with the wiring of pinch valves? Do you need the control circuit for operating pinch valves? Do you need pneumatic components for the switching? We are happy to help!

Pinch Valves Type VM

Pinch Valve with pneumatic sealing and flange connection. Range of Nominal Widths: DN 40 - DN 150 Operating Temperature: - 10°C bis + 120°C* Operating Pressure: max. 4 bar* Control Pressure = Operating Pressure: + 2 up to 2,5 bar * Operational limitations depend on nominal width, temperature and composite materials. Crucial are the parameters set in the confirmation.

Pinch valves in stainless steel (1.4301, 1.4404, Duplex, ..) with flanges, female and male threads, pipe ends, tri-clamp DIN 32676, threads acc. DIN 11853, clamp pipe connections (DIN 11864-3 / DIN 11853-3), screwed pipe connections (DIN 11864-1 / DIN 11853-1) and flange pipe connections ( (DIN 11864-2 / DIN 11853-2).

Couplings for pneumatic conveyors for a fast, safe and economic installation: DVK-HD® high pressure - heavy version for pressure conveying up to max. 12 bar from outer pipe diameter 60.3 mm till 206.0 mm DVK 6 for suction and pressure conveyors up to 6 bar and vacuum-resistant up to 5000 mm WH from outer pipe diameter 33.7 mm till 110.0 mm DVK-Z traction relief heavy version with bridge part to safeguard against axial forces DVK S with quick closure for quick opening and closing with clamping lever DVK-6 Fix for connecitons to coupling stations or for connections stainless steel to glass

The comprehensive range of WAMGROUP pipe diverters provides a solution for almost every problem in diverting material flows in the conveying and processing of bulk materials.

Anti-wear Elbows from SINT - Polymer

It comprises one WEICON Repair Stick Steel, a special repair tape made of fibreglass-reinforced plastic, assembly instructions and a pair of protective gloves. The repair tape is impregnated with a special resin and activated by contact with water. The Pipe Repair Kit can be processed without any additional tools and is used for the reliable and permanent sealing of cracks and leaks. It is very easy and quick to use and shows excellent adhesive properties, high pressure and chemical resistance as well as temperature resistance up to 150°C. Within 30 minutes, the tape is fully cured and hard-wearing. Due to the fabric properties of the tape, the resulting high flexibility and the simple processing, the repair kit is particularly suitable for sealing leaks in bends, T-pieces or in spaces difficult to access. It can be used on many different surfaces such as stainless steel, aluminium, copper, PVC, many plastics, fibreglass, concrete, ceramics and rubber.

Litronic-FMS 3K / RMH12 pipe sensor The Liebherr in situ water content determination Litronic-FMS 3K-RMH12 is used to detect the water content (concentration determination) even in very low ppm ranges in emulsions such as diesel fuel, transmission, hydraulic, engine, roller bearing, transformer and turbine oil as well as in battery systems. The sensors were developed in cooperation with the ISO/TS 16332 standardisation committee for the water separation ability of diesel fuel filters. The installation takes place on test and inspection stands and replaces the previous manual sampling as well as other offline measuring systems. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the system has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age.

PGR Drive Technologies provide solutions in planet gear units with PTO, IEC, parallel shaft input options which offer high reduction ratio in small volumes in drive systems with heavy and variable loads thanks to their compact and modular structure up to 850000 Nm of moment values.

Good planning is an important prerequisite for a successful project. We develop customer-oriented solutions in the field of bulk materials handling and can incorporate new innovations in the process. After an analysis of the situation at the customer's site, everything is adapted to the conditions on site during the planning phase. The construction work is performed in-house here. This offers two decisive advantages. On the one hand, information loss is avoided, and on the other, CAD modelling using Solid Works enables rapid visualisation and detailed presentation. The direct dovetailing with our own manufacturing ensures short distances - so corrections can also be made during the production phase without any further ado

We plan, manufacture, and assemble bulk material handling systems for screening, mixing, filling, emptying, conveying, dosing, and weighing. We always keep our customers' individual requirements in mind. We develop tailor-made turnkey solutions, from joint project definition to planning and manufacturing to commissioning. As your partner for demanding requirements in the field of bulk material handling systems, we offer you complete solutions with services from a single source: ◾In-depth, process engineering consulting ◾Compact, multifunctional system concepts ◾Testing of system concepts in our own technical center ◾Automation and control solutions ◾Design and construction of your solution ◾Manufacturing of your plant in our own production facility ◾Assembly and commissioning ◾CE marking ◾Validation and qualification in accordance with GMP and FDA ◾Reliable and transparent project management Plant services such as maintenance, spare parts service, training, and plant optimization round off our range of services.

- Suitable for all industrial requirements - Housing of high-strength alloy - Patented high pressure safety cylinder - Reinforced release shock absorber - 360° rotatable reaction arm - Torque range from 210 Nm to 65,000 Nm (155 to 47,940 ft lbs) - Hydraulic connections up to 800 bar (11,600 psi) operating pressure - For hexagonal (Allen) sockets, standard and safety nuts - Single or dual hose design - Including square socket adapter with safety coupling and 360° rotatable angle - Safety-Hold system as option - Also available for use in hazardous areas for zone I (gas), according to ATEX standard.

XVR / XVK: - Torque up to 8600 Nm (6,340 fl lbs) - Wrench sizes from 19 to 75 mm (3/4"to 3") - Switchable clockwise/anti-clockwise - Standardised or adjustable safety support LTX: - Made of special lightweight aluminium alloy