Application area: The silo overfill protection is suitable for preventing overfilling for silos to be filled pneumatically. It consists of a pneumatic pinch valve with electric solenoid valve in the filling line and a switch box. For the function, a maximum fill level limit switch must be provided by the customer on the silo and compressed air (approx. 6 bar) free of oil and water must be constantly available. The switch box is connected to 380 V, 50 Hz power supply. Electrical wiring and compressed air supply must be provided by the customer. The system must be switched on before the filling. Blowing in is not possible without electrical voltage. Electrical equipment: The pinch valve is closed in the normal state. It must be released by pressing a button before starting the filling. The use of the system can be signalled remotely by local equipment such as indicator lamp or similar. A signal to be set up by the customer (horn or similar) is triggered if the fill level reaches the maximum sensor. The delivery must be stopped immediately. The signal can be switched off at the switch box. After a specified (configurable) time, the pinch valve then closes automatically whereby any further filling of the silo is prevented. If the pinch valve has closed for full delivery, it can be opened again using a key switch by responsible operating personnel to flush out the fill tube with air to clear residue material. The valve must be closed again afterwards (Attention! The protection is not effective during actuation using the key switch!). A magnetic switch is attached to the fill tube coupling. The vibration motor of the silo ventilation filter is switched on by a pulse for 10 - 20 seconds when the blank coupling populated with magnets is removed. The vibration process repeats after completion of the filling when attaching the blank coupling. A version without automatic filter vibration is also optionally available. At high air injection pressure due to the final sloshing or in the case of soiled filter elements, overpressure in the silo can occur which exceeds the setting value of the overpressure valve. A pressure switch can be installed in the silo roof to prevent this risk. If the setpoint pressure is exceeded, the pinch valve closes automatically, the filter is cleaned and then the pinch valve opens again and the filling process can be continued until the maximum sensor is tripped.

With the Silo Scale Kit with IoT/Cloud remote monitoring, BOSCHE presents a modular solution at SOLIDS that enables online weight and fill-level monitoring for silos, tanks and containers—accessible via web portal or app. The system combines robust weighing technology with modern connectivity: an LTE-enabled IoT gateway securely transmits measurement data to the BOSCHE Cloud. This gives operators real-time transparency of stocks, improves replenishment planning and helps optimize processes across logistics, production and silo operations. For added operational safety, the solution supports real-time alerts when defined limit values are exceeded. Key features (selection): • D15N-MS load modules: statically calculated, up to 50 t capacity per module / silo leg, designed for demanding applications • High-quality stainless-steel load cells for long-term use in harsh industrial environments • JBD junction box (up to 6 load cells), IP67 – robust, field-proven design • CSS weight indicator with backlit LCD and RS232/USB interfaces for flexible integration • IoT gateway incl. cloud access: integrated SIM card, plug-and-play setup, event-based notifications

IFA Technology’s silo storage systems provide a powerful and reliable solution for handling and storing bulk materials such as building materials, chemical powders, fillers, or granulates. Each silo is engineered to support stable production processes and consistent material quality. Capacities & Construction Options: - Silo volumes ranging from 10 m³ to 200 m³ per unit - Construction materials: mild steel, stainless steel, plastic or FRP - Configurations tailored to material behaviour and process conditions The silos are designed to ensure a smooth material flow. Conical silo bases support consistent discharge and help prevent bridging, which is essential for the reliable handling of fine or poor-flowing products. Available Equipment & Features: - Discharge aids to support continuous material flow - Level sensors for reliable stock monitoring - Ventilation systems for maintaining product stability - Optional heating coils for controlled storage conditions For seamless integration into downstream processes, silo systems can be combined with vacuum or pressure conveying systems. This enables controlled material transfer from storage to production. Typical Application Areas: - Building materials (cement, sand, calcium carbonate) - Chemical industry (powders, additives, fillers) - Food raw materials (grain, flour) - Mineral products, logistics and industrial material supply Every silo system is engineered according to customer-specific requirements including capacity, material properties, environmental conditions and process integration. The result is a storage solution that ensures efficiency, operational reliability and consistent material quality.

REEL Möller GmbH offers a wide spectrum of silos for storage, blending or homogenization of bulk materials. Various constructions are available like dome silos, silos with flat bottom or with displacement cone, large capacity silos or intermediate storage facilities. Features • Concrete or steel structure, depending on size • Versions with a flat bottom, displacement cone (DCS silo) or central cone (MDS silo) for decompression • Discharge with pneumatic equipment • Discharge capacities up to way above 1000 m³/h • Large capacity silo for long term secure process supply • Storage capacity of up to 80.000 m³ and silo diameters up to 60 m are realized

The Stanelle PNEUFIX jet-filter is suitable for dedusting pneumatic and mechanical, continuous and discontinuous charging and conveying processes in silos and bunkers. The convincing features of the PNEUFIX are not only its rugged construction, but also its flexible application potential. In conjunction with a direct mounted extractor fan the PNEUFIX can also dedust conveyor belts, elevators, and other dust-laden environments. The PNEUFIX is also available in special vacuum and surge proof, heated and insulated, and explosion proof designs.

Transport Optimized With export separated silos you can save a large part of the freight costs. Each silo unit consists of a few crane packages. These include the complete silo, all the accessories such as railing, ladder, filling tube and dedusting filter as well as connecting parts and sealing material for assembly. The individual silo segments are stacked to save space. Arrived at the destination, the individual segments can be easily screwed together. The silos are available in diameters from 2,400 mm to 3,500 mm with a volume of 19 m³ to 180 m³. All components, e.g. Filters, overfill protection, inspection facilities and discharge aids are part of the delivery offer. We are also pleased to offer you corresponding mechanical or pneumatic conveyor systems for filling or emptying the silos.

Our groundbreaking technology is also prevalent in high capacity bulk storage and mixing silos. If you have higher capacity requirements, typically from 5,000 to 50,000 tonnes for free flowing bulk solids materials, Claudius Peters Technologies excels. For materials such as cement, lime, gypsum and alumina Claudius Peters supply a wide spectrum of silo types taking into consideration the characteristics of the material such as flow and storage conditions. Whatever specification you require, we will draw upon on our vast knowledge of different bulk materials and silo designs to deliver the optimum solution that will perform efficiently every time.

The SILVERLINE FE scraper is a pre-scraper and offers very gentle cleaning on the belt thanks to its spring-mounted and individually adjustable segments. This clever design ensures constant contact pressure and at the same time low maintenance. Thanks to its specially developed flexible design, low installation heights are also possible. The Scraper was developed so that it can also be used in high temperature ranges.

The SILVERLINE PU scraper is a pre-scraper that was specially developed and optimized for sticky materials. It is also particularly suitable for conveyor systems where belts of different thicknesses have been connected to one another. The segments made from the polyurethane mixture specially developed for us are particularly durable and therefore require little maintenance. We are currently developing a new heat-resistant polyurethane mixture together with our supplier so that this scraper can also be used in high temperature ranges.

In many applications simple mixing is not sufficient to get a product with a homogeneous quality. This is especially true when powders that tend to form agglomerates or gels (CMC, Xanthan, Carbopol, Locust bean gum, Alginate etc.) have to be mixed into liquids. This is the point where the capability of a mixing tool has to show its effect. Large area mixing does not help even when using a Jetstream mixer as the moment when the agglomerates leave the mixing head the turbulence in the liquid is not strong enough to destroy the lumps or agglomerates, and they float with the turbulence only. The best example is the treatment of the above mentioned powders. Conventional stirrers require a lot of energy and time to dissolve or break the lumps as the powder immediately forms a layer of gel at the surface and further powders then float at the surface level. The stirring element can [after some time], remove the layer but the small lumps, some less than a millimetre, can’t be broken down. Very often an additional processing step with a dispersing machine or a high pressure homogeniser is required. Especially for such applications a mixing and dispersing tool has been developed that offers a perfect compromise between large volume mixing (macro mixing) and required dispersing effect (micro mixing). The part of the mixing head that is responsible for the large volume mixing shows a similarity with the head of a Jetstream mixer, while the part for the dispersing looks like a batch rotor-stator high shear system. The performance of a DISPERMIX is in-between the performance of a Jetstream mixer and the shear capability of a batch disperser. Perfect applications are the dissolving of CMC powder; Carbopol; Plastisol colouring; Polymer solutions; cold emulsifying of aroma oil; production and suspending of juice concentrates; ice cream pre-mix; pre-Emulsifying of soft margarine; dessert-sauces of all kind; chocolate, and milk pudding; and pre-mixes, especially when hydro colloids have to be mixed into a liquid.

The SPTD single straight pipe plug diverter has been specially designed to route powders and pellets with minimum degradation in pneumatic conveying systems. The straight pipe makes the SPTD very suitable for applications in the food, pet food, plastics (recycling) and petrochemical industries. A smooth passage of product is guaranteed by precision machining, very effective sealing and a complete obstruction free passage. The user friendly fool proof design enables fast in situ internal examination, cleaning and, if necessary, replacement of seals. The design of the SPTD plug diverter conforms to all current legislation regarding safety in the workplace. Consequently there are no moving parts on the outside. The SPTD is available in 6 consecutive sizes from 150 up to 400. For smaller sizes we offer the SPTDS single straight pipe plug diverter, which is available in 5 consecutive sizes from 50 up to 125.

The SPTDS single straight pipe plug diverter has been specially designed to route powders and pellets with minimum degradation in pneumatic conveying systems. The straight pipe makes the SPTDS very suitable for applications in the food, pet food, plastics (recycling) and petrochemical industries. A smooth passage of product is guaranteed by precision machining, very effective sealing and a complete obstruction free passage. The user friendly fool proof design enables fast in situ internal examination, cleaning and, if necessary, replacement of seals. The design of the SPTDS plug diverter conforms to all current legislation regarding safety in the workplace. Consequently there are no moving parts on the outside. The SPTDS is available in 5 consecutive sizes from 50 up to 125. For larger sizes we offer the SPTD single straight pipe plug diverter, which is available in 6 consecutive sizes from 150 up to 400.

Mixer's field of application: * small production orders * preparation of master batches * "just-in-time" mixing jobs * product development Further characteristics: * Technically ideal mixing quality; adjustable mixing intensity (from gentle homogenization to intensive deagglomeration) * Micro-fine admixture of liquid material; the mixer remains dry and clean * Selection of filling level from 10% to 100% of working capacity * Ideal discharging of residues; easy cleaning/ sterilization (GMP Standard) * Integration into your ERP System, mixing programs supplied by PLC * A bar code scanner can be integrated for online-documentation * You need a limited infrastructure only: manual fork lift, scale and some standard drums Function: A patented spiral mixing tool rearranges the mixing goods. There is an upward movement in the periphery and a downward movement caused by gravity in the centre of the mixing vessel. You can improve the cross flow by inclining the mixing vessel up to 25 degrees. This mixing machine achieves technically ideal mixing qualities. Mixing goods can be dry, wet, suspended or pasty. According to the required processing/ mixing result (either gentle or aggressive and dispersive) you can select the mode of operation: gentle blending, deagglomeration, wetting at low energy input, wetting at high energy input, agglomeration, drying, improving of solubility etc.