This screening machine is ideally suited to separate and dedust dry, powdered and granular products. Particularly suitable for high feed rates and multi deck separations of fine, lightweight and difficult to screen products.

The current version of the pneumatic deck lifting system installed in tumbler screening machines, allows screen inserts to be changed one at a time. When used with multi-deck screening machines each deck has to be raised and changed separately. This is time and labour intensive, depending on the number of screen inserts to be changed. In order minimise downtime, GKM Siebtechnik has developed a new pneumatic multi-deck lifting system allowing multiple deck lifting and exchange in a single operation. By means of the pneumatic cylinders, all screening decks can be lifted simultaneously. All screen inserts can be inspected, cleaned or changed at once. This new lifting system allows between two and four decks to be the exchanged and inspected after which the complete screening decks are lowered precisely back to their correct location. This innovative pneumatic multi-deck lifting system can be installed or retrofitted on tumbler or vibrating screening machines with diameters of between 600 (one to three deck units) to 1200mm (from one to four deck units). Where access is limited, the system is particularly advantageous because only single-side access to the machine is necessary. When together used with the GKM quick-clamp system, time-consuming loosening and tightening of the nuts on the ten to twelve clamping screws, is eliminated as is the use of tools. In addition, the system guarantees a uniform deck clamping force. This latest pneumatic multi-deck lifting system has already been successfully implemented by well-known manufacturers in the chemical industry.

TURBO is the ideal high throughput system for the creation of single or multi-ingredient recipes. Using a proprietary bagging system that reduces operator labour and increases safety, ergonomics and traceability, Turbo provides completed formulations in sealed and barcoded bags to a maximum speed of one bag every 35 seconds.

In connection with pressure vessel systems the most economic pneumatic conveying system. Low energy consumption, low wear, and tear, high availability, reliable and long-lasting. Through MÖLLER® technology, REEL Möller GmbH has developed a pneumatic dense phase conveying system, which is particularly suitable for fine-grained mineral bulk materials such as fly ash, cement, lime, as well as primary and secondary alumina. The patented MÖLLER-TURBUFLOW® dense phase conveying system is characterized by an inner pipeline, the secondary pipeline, which ensures local turbulence by means of a port and diaphragm configuration. This assists the conveying process by fluidizing the bulk material. The result is slow and energy-saving conveying with high loading.

Turnkey plant engineering covers the entire project cycle from initial requirements analysis through planning, engineering, and manufacturing to installation, commissioning, and long-term service. Scope of services & process steps: - Consulting & requirements analysis: technical and economic evaluation of your project needs - Planning & development: detailed concept design with a focus on automation and process optimisation - Engineering & construction: mechanical design, process engineering, and control technology - Manufacturing & modular construction: high-quality production of plant components, including in-house stainless-steel fabrication, and welding - Installation & commissioning: professional on-site installation and a smooth start-up of the complete system - After-Sales & service: maintenance, expansion, and modernisation throughout the entire lifecycle of the plant Your benefits with IFA turnkey plants: → Single point of contact from initial idea to fully operational plant: planning, manufacturing, installation, and service from one source → Seamless integration of all process steps – weighing, mixing, dosing, storing, conveying and controlling: all perfectly coordinated → Quality and reliability – IFA delivers even complex systems to the highest standards, supported by its own manufacturing capacities → Process optimisation – improved material flow and efficient operations through professional planning, automation, and targeted engineering → Long-term service – after-sales support, maintenance, upgrades, and modifications ensure sustainable plant performance With its turnkey offering, IFA Technology demonstrates at SOLIDS how companies can implement complete solids and liquids production systems in a fully integrated and efficient way. Decision-makers gain access to a mature overall concept from raw-material handling and dosing to final processing with minimal effort and maximum process and quality reliability.

- Feeder ideal for difficult flowing, sticky or floodable bulk ingredients at low feed rates - Loss-in-weight feeder for poor flowing or floodable powders - Separate screw and agitator motors (3 phase AC gear motors), except models MT and DDSR20 - Interchangeable screws and screw tubes allowing quick adjustment to changing ingredients and feed rates

- Handles poor-flowing, sticky powders as well as fibers and pellets - A special negative angle wall hopper geometry and an diagonal agitator that prevents bridging and ensures optimal bulk material flow into the screw - Optimized mass flow and a uniform screw fill level - An add-on hopper for a total bulk storage of 50 dm³ (1.8 cuft)

KREISEL two-way distributors are used to direct the flow of bulk material optimally.

The Claudius Peters Two-Way Gate is installed in aeroslide systems to guide and control the mass flow. The Two-Way Gate consists of a cylindrical housing. Sealing of one outlet each is carried out by an adjustable gate. By turning the drive shaft, the gate shifts from one material outlet to the other. A flexible sealing ensures that the outlet is sealed dust-tight. The drives can be pneumatic, motoric or manual and are designed with sufficient reserves so that even under aggravated conditions a safe operation is ensured. For cleaning of the Two-Way Gate and for inspection of the gate sealing, the housing is equipped with a large inspection cover. Replacement of the wear parts (aeration fabric and gate sealing) can take place while the Two-Way Gate remains installed by disassembling the top cover or the bottom. Lubrication of the bearings or the drive is not necessary. The end positions can be precisely adjusted and can be indicated by limit switches integrated in the drive.

Application area: The tube switch is mainly used in delivery lines of high pressure systems; however it can also be used in the low pressure range at any time. It is suitable for the transport of dry, non-adhesive or tending to cake dusts and is used for changing the direction of the delivery flow. Material: Case: grey cast iron or cast stainless steel Shut-off cone: grey cast iron or cast stainless steel Seal: rubber, silicone, Viton Design: The tube switch consists of the tube switch case, the swivel arm with the shut-off cone and the pneumatic swivel drive. The closed outlet is sealed with a sealing ring which is pressed against a hardened ring. Electrical equipment: The tube switch has a limit switch (normally closed contact and normally open contact) in each end position at free choice for standard signalling. A Herion 5/2 way solenoid valve is usually used as control valve (other makes of control valve on request). The electrical equipment is supplied in any protection type and any common voltage according to requirement. Operating data: control pressure: approx. 5 bar operating pressure: max. 10 bar Special features: The tube switch guarantees faultless sealing of the stopped delivery stream so that material mixtures in the case of conveying different materials via one system are ruled out. The advantage of this design is that the sealing rings can be replaced without dismantling and shortest standstill times. A different switch design must be selected for the conveyance of adhesive and caking materials. The tube switch can of course also be supplied with electric motor drive and with manual actuation.

Super fine grinding plants, grinding and drying plants and simultaneous grinding and drying plants, type ULTRA-ROTOR, especially for: food, minerals (drying free of agglomerates), vegetables and animal proteins, special chemicals and everything which is difficult to be treated on conventional plants. ULTRA-ROTOR plants treat sticky materials, explosive materials and corrosive materials. They are used as grinders, dryers, mixers, as well as for surface coating (coating of minerals with stearic acid). From individual machines to complete plants and subsystems is our scope of delivery. Minimal wear and tear costs due to particle to particle interaction. Heavy robust construction, extremely long and trouble free operation. We customize each application to the individual customer's requirements. Cryogenic grinding, grinding under inert atmosphere, grinding and drying under steam atmosphere are available.

This system prevents sticking and adhering of dry bulk materials to the inner metal surfaces and ensures a continuous product discharge

Umlenkrolle für Reißleine

By contrast with the filter elements in the BFE filter, the cartridge filters are almost always flowed against from below. The regeneration of the elements also takes place using compressed air. The main advantages of the cartridge filters are the overall more compact design of the filter and the high operating temperature of max. 260°C. These are normally raw gas flows from thermal processes. You would like to know more about the umtec cartridge filters? Go ahead and ask us about them!